Picture this; You wake up up in the morning, and also you try to turn on your gamecube; you press the button, and also you hear a whirring noise, however nothing else happens. NOOOOOO! the guys are coming over to beat Super quit Bros. In a pair of hours, and the gamecube doesn"t work! before you launch right into a bunch of "that"s what you get for buying a gamecube. Loser!"", i know, ns don"t desire to hear it. Because that those of you who love her cube, though, ns hope this helps.
You are watching: Gamecube turns on but no picture
If there has recently to be a strength surge whereby you live, that might be responsible for the problem you room having. The symptoms space as follows: the exterior power supply features normally, but when you plugin the cube and push the power button, the fan transforms on, yet nothing rather happens; no light, no video, no turn disc, nothing. Nothing you do transforms this condition. So what"s wrong? is the gamecube fried? The Nintendo maintenance procedure for fixing this trouble is to replace the whole board, which, obviously, is expensive and also wasteful; the only component that"s fried, together it turns out, is the fuse, which, for reasons I will never understand, Nintendo went out of its means to hide deep inside the system. I"m going to tell you just how to take the mechanism apart and replace the fuse v a cheap, identical fuse from radio shack or an additional electronic components supplier.
You will certainly need;A fuse; the must it is in a 5 amp, quick acting fuse (I don"t understand if you can safely use slow-blow). Any fuse rated reduced will blow, and also any fuse rated higher will fried food the system. A load of 5 of these costs around $5.00 U.S. At radio shack, and also probably less elsewhere.Some wire; nothing special, but I found some thin, stranded cable to be really cooperative.Something to open the Nintendo screws with; this can be either an main Nintendo screwdriver or a cheap Bic pen (more on this later).A phillip"s head screwdriver; you need to probably have several, to insurance the ideal size.A soldering iron and solder; optional, but very helpful; if girlfriend don"t currently know exactly how to solder, I highly recommend friend learn; it"s easy and effective.A multimeter; not necessary, but useful if you want to it is in absolutely certain what the trouble is.Some electric tape, cable cutters, and a TV to test it on.
Many civilization seem cynical to open up the gamecube; I"m not really certain why. Maybe it"s because the screws that organize it with each other are kind of hidden. Here"s just how to discover them. Rotate the cube over so you"re looking at its underside. You should see four round wells, one at each corner. In ~ the bottom of each, over there is a hex-headed Nintendo screw. These 4 screws are all the is hold the top and bottom halves that the cube together. Remove them; that should be straightforward enough with an main Nintendo screwdriver. If you don"t have one, traction the octopus tube out of one of those cheap Bic pens, and also that will fit nicely end the head of the screw, enabling you to rotate it out. You have to push under a bit. Don"t usage an old pen; the plastic will be too degraded. Fortunately, new ones price only a dollar a pack. With all 4 screws removed, rotate the cube back over, and gently background the upper covering off. Then continue to the next step.
With the peak off, you need to see mainly metal Faraday shielding. Discover the port whereby the power brick plugs into the cube. It need to be an installed on a little plastic assembly that has the fan and also power button. Take off the screws that hold it right into place (there are only philip"s head screws ~ above the inside) and also lift the assembly off ( it will certainly still be hanging native a wire; don"t pull that off!). Now remove every the screws about the sheet of the steel shielding, including the four small screws over the storage card slots (you deserve to remove the controller port assembly by advertise in 2 plastic tabs in ~ its sides and also pulling it up and also forward together necessary. The is plugged right into the mechanism by a flat cable that deserve to be easily plugged back in again later). As soon as all the screws room out, lift turn off the Faraday shielding, together with the disc drive (which, like the controller port assembly, is simply plugged right into the board, and can be quickly plugged back in again later). You should now be looking in ~ the ceiling board.
So whereby is the fuse? Look at the edge of the plank , whereby the cable from the power assembly enters the actual love of the system. Right beside this connection, you need to see a small, white ingredient with metal caps ~ above both ends, and the letter "KOAC 5A" composed on it. This is the fuse, and the component we doubt is blown. Girlfriend can check it through a continuous meter. If the fuse is good, there need to be zero resistance. My fuse had actually some conductivity, yet was clearly blown. If girlfriend want much more proof, plug in the power brick, press the power button, and also do the following; put the black probe of your multimeter ~ above the grounding piece that goes all the method around the board, and the red probe on the end of the fuse closest to the power connector; you have to read about 12 volts. Now examine the other finish of the fuse; if it to be working, girlfriend would get 12 volts there too. If it"s blown, you"ll acquire no strength at all. Currently you"ve determined the problem, it"s time to deal with it.
First, solder or otherwise affix wires to both ends of the old fuse. This have the right to be tricky, yet be persistent. You might de-solder it and replace it through an the same one, yet there"s no point; this works simply as well. Now attach the various other ends the the wires come the ends of the brand-new fuse; ns used small metal fuse clamps, yet you could just pave the wires approximately the ends of the fuse and also tape castle in place, or also solder lock on. Plunder the fuse in ice so it won"t short out versus anything, and place it in a practically spot top top the circuit board where it won"t roll around too much. Make certain all your relationships are for sure (polarity doesn"t matter, as a fuse is basically a wire), and close the cube ago up again; plug everything back in, snap< and screw every the assemblies bakc on, et cetera, et cetera. Putting it back together is easy once you"ve taken the apart.
See more: Write A Balanced Ionic Equation For This Acid-Base Reaction: 2Csoh(Aq)+H2So4(Aq)→
Now the you have it closed up, plug that in, and try to revolve it on. The should role normally. If that doesn"t rotate on, friend may have a poor connection. If it transforms of because that a second, and also then blows out again, you provided the dorn fuse, despite my warning. Open it earlier up and also replace it through the appropriate one. If it powers up normally, congratulations! friend now have actually a functioning gamecube! to ensure the fuse doesn"t punch again if there"s one more power surge, girlfriend should probably plug the system into a surging protector.